5 Commits

Include renames

Author	SHA1	Message	Date
steveandClaude Opus 4.8	3af0d08779	Fill: plant nothing for a region that misses the object entirely ... clampTo INVERTS a region lying wholly outside the object — Max clamps below Min — rather than emptying it. The old loop-until-past-MaxX form handled that for free by never entering the loop. Counting positions up front does not: a region 500cm east of a bed with ±50cm local bounds produced 4 plops at x=275, a couple of metres off the bed. Caught by removing the guard and watching the new test fail, not by assuming it would. Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]> Claude-Session: https://claude.ai/code/session_01H3zbym8Doka2d7D48maSgZ	2026-07-21 10:13:33 -04:00
steveandClaude Opus 4.8	45da4b15e2	Fill: honour the half-spacing edge rule when packing plops (#75) ... Filling a bed left the outer row too far from the edge, and staggered rows worse still. Two defects, both from anchoring the lattice at the region's min corner: - Odd rows offset by `radius` started at `MinX + 2·radius`, leaving a bare strip a whole plop wide down one side of every other row. - All the leftover slack piled up on the far edge, where plops hung 13cm outside the bed on a 4×8ft garlic bed. Nothing clips them, so they drew over the bed outline. Spacing is a constraint between neighbouring plants competing for the same soil, light and water. A bed edge is not a competitor, so the outer row owes it half the spacing — the arithmetic inside every square-foot-gardening chart (4/square = 6" apart, 3" from the square's edge). The wrinkle: a plop is a CLUMP, not a plant. defaultPlopRadius is 1.5×spacing, so keeping the whole circle inside the bed insets the outer row by 1.5 spacings, three times what the rule allows. So centre the lattice and set the minimum centre-inset to `radius - spacing/2`: the clump may cross the edge by up to half a spacing, putting its outermost plants exactly the half-spacing from the edge the rule asks for. Capped there — a clump mostly outside the bed would be a drawing of plants in the path. Same bed, same 15 plops, now symmetric with a deliberate 6.5cm overhang inside the 7.5cm budget instead of an accidental 13cm on one side only. The stagger falls out of the centring for free: an offset row holds one fewer plop, and centring that run puts it exactly half a pitch off its neighbours. TestFillRegionDeterministicPacking expected 4 plops in a 60×60 bed; the fourth was centred ON the east edge with half of it outside, well past the budget. It is 3 now — the fix working, not a regression in it. Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]> Claude-Session: https://claude.ai/code/session_01H3zbym8Doka2d7D48maSgZ	2026-07-21 10:11:08 -04:00
steve	8c5ddb21ec	Season view: filter the editor to a year (#54) (#66) ... Co-authored-by: Steve Dudenhoeffer <[email protected]>	2026-07-21 05:47:34 +00:00
steve	f208da94d6	Revision history: change sets + revisions + revert — the undo substrate (#48) (#61) ... Co-authored-by: Steve Dudenhoeffer <[email protected]>	2026-07-21 05:07:30 +00:00
steve	18e4a299c2	Agent seam: bulk ops (FillRegion/ClearObject/DescribeGarden) + DefineTool wrappers (#19) ... Co-authored-by: Steve Dudenhoeffer <[email protected]>	2026-07-19 05:16:40 +00:00